Front Steering Sway Bar Inner Outer Tie Rod End Suspension For 2000-2005 LeSabre

Fitting the Following vehicle: 2000-2005 Buick LeSabre 2006-2011 Buick Lucerne 1997-2005 Buick Park Avenue 1997-1999 Buick Riviera 2000-2005 Cadillac DeVille 2006-2011 Cadillac DTS 1999-2003 Cadillac Seville 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville Package Includes: 2x Front Inner Tie Rod End -EV2602x Front Outer Tie Rod End -ES34522x Front Sway Bar End Link -K5255 Note (2). Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts 10 Year Warranty This item is backed by our 10-year warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only Tie-Rod End Replacement Guideline: This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance 1.Lift the vehicle and dismount the front axle wheels 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes 3.Dismount the front underride guard 4.Loosen the fastening nut from the tie rod and remove it completely 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator 6.Remove the clamp of the bellow on the steering gear 7.Push the bellow towards the tie rod end 8.Unscrew the inner tie rod from the rack 9.Clean the sealing face of the bellow at the steering gear 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle Note:Always use new self-locking nuts and bolts for a reliable repair 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer 12.Mount the bellow and close the clamps with the appropriate special tool Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure Tip:Secure the ball stud against twisting with a suitable tool 14.Mount the front underride guard 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications 17.Perform a test drive Frequently Asked Questions (1).What are the symptoms of a bad sway bar? (2).What happens when a sway bar breaks? Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads (3).Stronger inclination of the vehicle during cornering If the sway bar stabilizer link is found to be defective, it should be replaced as described below 1.Raise vehicle and remove front wheels Tip:Always check both stabilizer links and replace them in pairs if necessary 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove Tip:If the ball stud also starts to turn, hold it with a suitable tool 4.Press stabilizer link out of torsion bar 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it 6.Press stabilizer link at suspension strut out of bracket 7.Insert new stabilizer link at suspension strut 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer 9.Insert new stabilizer link at stabilizer 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension 12.Conclude with a test drive (1).Why should I get my tie rods inspected on a regular basis? (2).Vibrations (3).Shaking (4).Wandering