Thermostat Temperature Controller For Refrigeration Freezer

XR06CX-4N1F1 descriptionThe is also provided with 2 NTC probe inputs, the first one for temperature control and the second one to be located onto the evaporator, to control the defrost termination temperature and to manage the fan and it's provided with a configurable digital input. With the HOTKEY it's possible to program the instrument in a quick and easy way. Specification Supply Voltage: 120V/AC Sensor type: NTC Buzzer: Yes Display unit: ℉/℃ Compressor load current: 20A Operating Temperature: 32~140℉(0~60℃) Applicable temperature range: -40~210.2℉(-40~99℃) Product Dimensions: Front 1.26' x 2.91' (32x74 mm); Mounting dimensions: Opening 2.79' x 1.14'(71x29 mm) Built-in depth: 2.36' (60 mm) Medium-low temperature, forced air-cooled, electrically heated or hot air defrost thermostats Defrost Two defrost modes are available through the "td " parameter: td=EL defrost through electrical heater (compressor OFF) td=in hot gas defrost (compressor ON). Other parameters are used to control the interval between defrost cycles (id) ), its maximum length (Md) and two defrost modes: timed or controlled by the evaporator's probe. At the end of defrost dripping time is started, its length is set in the dt parameter. With dt=0 the dripping time is disabled. Instrument and Mounting Instrument gases, excessive dirt or humidity. The same recommendations apply to probes. Let air circulate by the cooling holes. Package List 1*Manual 1*Thermostat Controller 2*Temperature Sensor 2*Special Bracket XR02CX-5N0C1 Description Model digital thermostat with off cycle defrost designed for refrigeration applications at normal temperature. It provides a relay output to drive the compressor. It is also provided with 1 NTC probe input and one configurable digital input. The instrument is fully configurable through special parameters that can be easily programmed through the keyboard or the by HOTKEY. Specification Supply voltage: 230V/AC Sensor type: NTC Buzzer: No Display unit: ℉/℃ Compressor load current: 20A Operating Temperature: 32~140℉(0~60℃) Applicable temperature range: -40~210.2℉(-40~99℃) Product dimensions: Front 1.26' x 2.91' (32x74 mm); Mounting dimensions: Opening 2.79' x 1.14'(71x29 mm) Built-in depth: 1.97' (50mm) Cooling/Heating/Stop Defrost Type Thermostat Defrost Defrost is performed through a simple stop of the compressor. Parameter "id" controls the interval between defrost cycles, while its length is controlled by parameter "Md" . Instrument and Mounting The instruments shall be mounted on vertical panel, in a 1.14' x 2.79'(29x71 mm) hole, and fixed using the special bracket supplied. The temperature range allowed for correct operation is 32~140℉(0-60℃). Avoid places subject to strong vibrations, corrosive gases, excessive dirt or humidity. The same recommendations apply to probes. Let air circulate by the cooling holes. Package List 1*Manual 1*Thermostat Controller 1*Temperature Sensor 2*Special Bracket refrigerating units. It provides two relay output: one for compressor and the other one for alarm signaling or as auxiliary output. It provides an NTC probe input and a digital input for alarm signaling, for switching the auxiliary output or for start defrost. The instrument is fully configurable through special parameters that can be easily programmed through the keyboard or the by HOTKEY. Specification Supply voltage: 230V/AC Sensor type: NTC Buzzer: No Display unit: ℉/℃ Compressor load current: 20 A Operating Temperature: 32~140℉(0~60℃) Applicable temperature range: -40~210.2℉(-40~99℃) Product dimensions: Front 1.26" x 2.91" (32x74 mm); Mounting dimensions: Opening 2.79" x 1.14" (71x29 mm) Built-in depth: 1.97" (50mm) Normal temperature, stop frost, additional alarm/bank light output type thermostat Defrost Defrost is performed through a simple stop of the compressor. Parameter "id" controls the interval between defrost cycles, while its length is controlled by parameter "Md" . Instrument and Mounting Instrument range allowed for correct operation is 32~140℉(0-60℃). Avoid places subject to strong vibrations, corrosive gases, excessive dirt or humidity. The same recommendations apply to probes. Let air circulate by the cooling holes. Package List 1*Manual 1*Thermostat Controller 1*Temperature Sensor 2*Special Bracket